Fabrication of a Novel Electrochemical Sensor for Simultaneous Determination of Toxic Lead and Cadmium Ions


Mehdi Sheikh Arabi 1 , 2 , * , Changiz Karami 3 , Masoud Ghanei-Motlagh ORCID 2 , **

1 Infectious Diseases Research Center, Golestan University of Medical Sciences, Gorgan, Iran

2 Medical Cellular and Molecular Research Center, Golestan University of Medical Sciences, Gorgan, Iran

3 Nano Drug Delivery Research Center, Kermanshah University of Medical Sciences, Kermanshah, Iran

Corresponding Authors:

How to Cite: Sheikh Arabi M , Karami C , Ghanei-Motlagh M. Fabrication of a Novel Electrochemical Sensor for Simultaneous Determination of Toxic Lead and Cadmium Ions, Ann Mil Health Sci Res. Online ahead of Print ; 17(4):e99082. doi: 10.5812/amh.99082.


Annals of Military and Health Sciences Research: 17 (4); e99082
Published Online: December 31, 2019
Article Type: Research Article
Received: October 23, 2019
Revised: December 19, 2019
Accepted: December 22, 2019

Background: Highly sensitive and rapid monitoring of heavy metal ions such as lead and cadmium has attracted considerable interest in analytical chemistry due to serious environmental effects of these ions.

Objectives: In this work, clay/carbon nanocomposite modified with an organic ligand was applied as a novel modifier for simultaneous measurement of Pb (II) and Cd (II) in water samples.

Methods: The characterization of the modifier was studied by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy. The analytical performance of the method was investigated by the differential pulse anodic stripping voltammetric (DPASV) technique using a carbon paste electrode (CPE) modified with the prepared nanocomposite.

Results: Under the selected optimized conditions, a linear voltammetric response in the range of 2.0 - 100.0 ppb was obtained for the both analyte ions. The calculated detection limits (S/N = 3) were found to be 1.1 ppb for Pb (II) and 0.7 ppb for Cd (II), which are below the World Health Organization (WHO) guideline values for lead and cadmium in drinking water. The method was successfully applied for determination of noxious Pb (II) and Cd (II) ions in real waters with acceptable recoveries for the spiked samples.

Conclusions: A simple, selective and sensitive electrochemical sensor was prepared and applied for simultaneous detection of Pb (II) and Cd (II). The suggested sensor demonstrated good electrochemical performance and anti-interference capability for electrochemical detection of these ions in real water samples using the DPASV method.


Nanocomposite Sensor Heavy Metals Voltammetry

Copyright © 2019, Annals of Military and Health Sciences Research. This is an open-access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International License (http://creativecommons.org/licenses/by-nc/4.0/) which permits copy and redistribute the material just in noncommercial usages, provided the original work is properly cited.

1. Background

Nowadays, there is an increasing demand to monitor heavy metal ions such as lead and cadmium due to their serious environmental impact (1). The World Health Organization (WHO) has set action levels for lead and cadmium in domestic water at 3 and 10 ppb, respectively (2). Therefore, it is highly important to develop sensitive and rapid monitoring techniques for detection of Pb (II) and Cd (II) in water samples. So far, different analytical protocols have been developed for sensing heavy metals such as flame atomic absorption spectrometry (FAAS) (3), graphite furnace atomic absorptions spectrometry (GF-AAS) (4), inductively coupled plasma optical emission spectrometry (ICP-OES) (5), inductively coupled plasma mass spectrometry (ICP-MS) (6) and fluorescence spectrometry (7). However, these methods require high implementation and maintenance costs as compared to different electrochemical methods for sensing Pb (II) and Cd (II) (8-10). The performance of electrochemical sensors depends on electrode modifiers (11). Among various modifiers, carbon nanostructures such as graphene (Gr) and carbon nanotube (CNT) have been employed for fabrication of electrochemical sensors in heavy metals (12, 13). However, application of Gr and CNT based modifiers is unfavorable from the economic point of view (14).

Sepiolite is a fibrous clay mineral with a unit cell formula of Si12Mg8O30(OH)4(OH2)4·8H2O (15). This clay material has lower cost compared to other commercial nanostructures and can be mined from the corresponding deposit as a raw mineral. However, sepiolite is not effective for electrochemical sensing applications due to its non-conductive property. Incorporation of carbon into clay material can be an effective way to improve the conductivity of natural clay materials (16). Moreover, surface modification of carbon substrate with organic ligands has been recognized as a potential strategy to improve the selectivity of modifiers in electroanalytical detection of heavy metals (17, 18).

2. Objectives

In this paper, clay/carbon nanocomposite was designed and used as substrate for preparation of a new electrode modifier. To improve the selectivity of the modifier, the prepared clay/carbon nanocomposite was modified with 3-[2-(2-aminoethylamino)ethylamino]propyl-trime thoxysilane (AAAPTS), as shown in Figure 1. The electrochemical properties of the clay-based modifier were investigated in detail. The prepared sensor showed remarkable sensitivity and good selectivity toward detection of Pb (II) and Cd (II) in water samples.

The schematic illustration of the modifier preparation
Figure 1. The schematic illustration of the modifier preparation

3. Methods

3.1. Materials and Apparatus

Sepiolite was obtained from a sepiolite mine (Fariman, Iran) with a particle size of ≤ 0.075 mm. Glucose, AAAPTS, graphite powder and silicon oil were obtained from Merck. Cd (II) and Pb (II) standard solutions (1000 ppm) were prepared by dissolving desired amounts of Cd(NO3)2·4H2O and Pb(NO3)2·4H2O (both from Merck), respectively, in deionized water. All other reagents were of analytical grade and were supplied from Merck. The supporting electrolyte employed in this work was acetate buffer (HAc-NaAc, 0.1 M), which was prepared throughout mixing solutions of acetic acid and sodium acetate.

All electrochemical data were acquired using a Metrohm computrace electroanalyzer Model 757 VA (Herisau, Switzerland). FT-IR spectra were recorded in the range of 400-4000 cm-1 on a PerkinElmer Spectrum 2000 FT-IR spectrometer (Norwalk, CT, USA) using the standard KBr disk method. Scanning electron microscopy (SEM) and the energy-dispersive X-ray (EDX) spectroscopy analysis were performed on a CARL ZEISS-AURIGA 60 microscope (Jena, Germany). The XRD pattern was recorded via a PANalytical Empyrean X-ray diffractometer (Almelo, Netherlands).

3.2. Preparation of Modifier

Clay/carbon nanocomposite was prepared by the hydrothermal method. For this purpose, 0.5 g of clay material was dispersed in 75 mL of deionized water by sonication. Then, 3.5 g of glucose was added and dissolved in the above suspension. The mixture was transferred into a Teflon-lined autoclave (100 mL capacity) and heated at 180ºC for 6 h. The obtained brown precipitate was first washed with distilled water and then dried at 70ºC for 24 h. In the next step, the product was heated at 650ºC for 3 h under N2 condition to improve the degree of carbonization.

The modification of clay/carbon nanocomposite with AAAPTS ligand was carried out by a simple reflux method. Briefly, 0.5 g of clay/carbon nanocomposite was suspended in 50 mL of toluene and then 3 mL of AAAPTS was added to the suspension. The mixture was refluxed at 75ºC overnight. The prepared product, as the modifier, was separated and repeatedly washed with toluene and ethanol. Finally, the resulting clay/carbon/AAAPTS nanocomposite was dried at room temperature.

3.3. Electrode Fabrication

The modified CPE was fabricated according to the literature methods (19, 20). Briefly, appropriate amounts of graphite powder (57.5% - 70% w/w), clay/carbon/AAAPTS nanocomposite (0% - 12.5% w/w) and silicone oil (30% w/w) were mixed using a mortar and pestle. Then, a portion of the achieved paste was packed into a Teflon tube (with a 2 mm inner diameter and a 10 cm length) in contact with a copper wire for electrical connection. The external surface of the prepared electrode was polished and smoothed on a paper surface before each electrochemical test.

4. Results

The FT-IR spectrum of the clay/carbon/AAAPTS nanocomposite is shown in Figure 2. The characteristic peak around 1032 cm-1 was attributed to the plane vibrations of Si-O-Si groups (21). The bands at 3560 and 1620 cm-1 were related to the stretching and bending vibrations of zeolitic water, respectively (22). Moreover, the band at 693 cm-1 was assigned to the bending vibration of Mg-O groups (23), and the band at 1467 cm-1 was ascribed to the stretching of C-N stretching bonds (24). The absorption band around 2922 cm-1 was due to the C-H stretching vibration of ethylene groups in AAAPTS (25).

The FT-IR spectrum of the clay/carbon/AAAPTS nanocomposite
Figure 2. The FT-IR spectrum of the clay/carbon/AAAPTS nanocomposite

The crystalline structure of the prepared nanocomposite was studied by XRD analysis. As shown in Figure 3, the diffraction peaks at 2θ = 7.3º (110), 12.2º (130), 19.9° (060), 20.7º (131), 26.5º (080), 35.1º (441) and 40.2º (541) corresponded to the standard pattern of sepiolite (JCPDS card No. 13-0595) (26). Moreover, no obvious peak was observed for carbon in the prepared nanocomposite. This may be due to the amorphous structure of the carbon deposited on the clay material.

The XRD pattern of the clay/carbon/AAAPTS nanocomposite
Figure 3. The XRD pattern of the clay/carbon/AAAPTS nanocomposite

The SEM image of the clay/carbon/AAAPTS nanocomposite is illustrated in Figure 4. The clay material obviously had a fibrous structure. In addition, the EDX spectrum revealed the presence of carbon, nitrogen, oxygen, magnesium and silicon in the prepared nanocomposite. Based on the above results, it can be concluded that the clay/carbon/AAAPTS nanocomposite is successfully synthesized.

(A) The SEM image and (B) EDX spectrum of the clay/carbon/AAAPTS nanocomposite
Figure 4. (A) The SEM image and (B) EDX spectrum of the clay/carbon/AAAPTS nanocomposite

5. Discussion

The DPASV responses of different electrodes including bare CPE, CPE-clay, CPE-clay/carbon and CPE-clay/carbon/AAAPTS in buffer solution (pH = 4) containing 25 ppb of Pb (II) and 25 ppb of Cd (II) are shown in Figure 5. As can be observed, the highest sensitivity was obtained at CPE-clay/carbon/AAAPTS. Therefore, the modified electrode was applied in the present study for simultaneous measurement of Pb (II) and Cd (II).

Stripping voltammograms of different electrodes in acetate buffer solution (0.1 M, pH = 4) containing 25 ppb of Pb (II) and 25 ppb of Cd (II). Other conditions: modifier amount = 7.5 %, accumulation potential = -1.1 V, accumulation time = 240 s.
Figure 5. Stripping voltammograms of different electrodes in acetate buffer solution (0.1 M, pH = 4) containing 25 ppb of Pb (II) and 25 ppb of Cd (II). Other conditions: modifier amount = 7.5 %, accumulation potential = -1.1 V, accumulation time = 240 s.

To improve the sensitivity of CPE-clay/carbon/AAAPTS toward detection of Pb (II) and Cd (II), some important experimental factors such as solution pH and modifier amount were examined and optimized. The influence of buffer pH (2.0 - 6.0) on the DPASV responses of CPE-clay/carbon/AAAPTS is demonstrated in Figure A6. As observed, the peak currents first increased with increasing the pH value up to 4 and then decreased at higher pH values. Thus, an optimum pH of 4.0 was selected in the next electrochemical experiments.

Voltammetric currents of CPE-clay/carbon/AAAPTS as function of (A) buffer solution pH and (B) the amount of modifier in the carbon paste
Figure 6. Voltammetric currents of CPE-clay/carbon/AAAPTS as function of (A) buffer solution pH and (B) the amount of modifier in the carbon paste

Further, the effect of the clay/carbon/AAAPTS amount was investigated on the response of the modified electrode. As shown in Figure 6B, the peak responses first increased with the amount of modifier in the carbon paste up to 7.5% (mass/mass) and then decreased at higher modifier content. By taking into account these results, a carbon-paste composition of 7.5% clay/carbon/AAAPTS, 62.5% graphite powder and 30% (mass/mass) silicon oil was employed for construction of the chemically modified electrode.

The calibration plot of CPE-clay/carbon/AAAPTS for Pb (II) and Cd (II) under optimum conditions is presented in Figure 7. The linear concentration range of 2.0 - 100.0 ppb for the both ions was achieved via CPE-clay/carbon/AAAPTS. The detection limit of the present sensor was found to be 1.1 ppb and 0.7 ppb for Pb (II) and Cd (II), respectively. The detection limit of the proposed sensor was also compared with those of some previously reported sensors (27-31) for analysis of Pb (II) and Cd (II) (Table 1). As can be observed, the detection limit of the prepared sensor was lower than the limits of other reported techniques. Moreover, the present procedure showed good reproducibility with a relative standard deviation (RSD) values of 4.5% for Cd (II) and 3.8% for Pb (II) at seven individually prepared electrodes in a solution containing 25 ppb of each ion.

Simultaneous detection of Pb (II) and Cd (II) at various concentrations. The insets show the calibration plots under optimal conditions.
Figure 7. Simultaneous detection of Pb (II) and Cd (II) at various concentrations. The insets show the calibration plots under optimal conditions.
Table 1. Comparison of CPE-Clay/Carbon/AAAPTS and Other Modified Electrodes for Determination of Pb (II) and Cd (II)
Electrode ModifierElectrode TypeDetection Limit (ppb)Ref.
Pb (II)Cd (II)
Alkalization-intercalated Ti3C2GCE8.511.0(27)
Multiwalled carbon nanotubesGCE6.68.4(28)
Bismuth oxideSPE816(30)
Ammonium tetrafluorobismuthateCPE1.29.8(31)
Clay/carbon/AAAPTSCPE1.10.7This work

Abbreviations: CPE, carbon paste electrode; GCE, glassy carbon electrode; GECE, graphite-epoxy composite electrode; SPE, screen-printed electrode

The selectivity of the method was also investigated. According to the experimental results, the analysis of Pb (II) and Cd (II) (at the concentration of 25 ppb) was not affected by a 20-fold excess of Ni (II), Co (II), and Mn (II); 10-fold excess of Hg (II) and Zn (II); and 5-fold excess of Cu (II). Accordingly, CPE-clay/carbon/AAAPTS can be applicable for selective detection of Pb (II) and Cd (II) in real samples.

The application of CPE-clay/carbon/AAAPTS was investigated for simultaneous determination of Pb (II) and Cd (II) in tap water, dam water and wastewater samples. The standard addition method was applied in the recovery tests, and the acquired results are reported in Table 2. Typical stripping voltammograms of CPE-clay/carbon/AAAPTS as well as different concentrations of metal ions in tap water samples are shown in Appendix 1 in Supplementary File. It is evident that the suggested electrochemical sensor is capable of determining the concentration of the both analyte ions in real water samples without any significant interferences and matrix problems. To verify the method accuracy, this procedure was applied for determination of Cd (II) and Pb (II) in a synthetic sample. The analytical results are presented in Appendix 2 in Supplementary File. As can be observed, the obtained results were in good agreement with the reference values and there was no significant differences between the results and the accepted values.

Table 2. Determination of Pb (II) and Cd (II) in Water Samples (N = 4)
SampleMetal IonAdded (ppb)Found (ppb)Recovery (%) + RSD
1 (Tap water, Gorgan, Iran)Pb (II)0--
10.09.797.0 ± 3.4
20.020.5102.5 ± 2.1
Cd (II)0--
10.010.3103.0 ± 2.8
20.019.698.0 ± 2.3
2 (Urban wastewater, Gorgan, Iran)Pb (II)06.2-
10.016.4102.0 ± 4.3
20.025.998.5 ± 5.4
Cd (II)04.3-
10.014.8105.0 ± 4.0
20.024.6101.5 ± 4.8
3 (Toshan Dam, Gorgan, Iran)Pb (II)0--
10.010.1101.0 ± 3.8
20.019.798.5 ± 4.1
Cd (II)0--
10.09.898.0 ± 4.6
20.020.4102.0 ± 3.9

5.1. Conclusions

In this study, a novel electrochemical sensor was introduced for sensitive analysis of cadmium and lead ions in water resources. Due to the good synergistic integration of the materials in the clay/carbon/AAAPTS modifier, the sensor showed high sensitivity and good selectivity for analysis of analyte ions. Under the optimum conditions, the detection limit of the proposed sensor was 1.1 ppb and 0.7 ppb for Pb (II) and Cd (II), respectively, well below the WHO guideline. In addition, the electrochemical method indicated good selectivity for measuring analyte ions in presence of some common interfering species. Finally, the sensor was utilized as a powerful tool for quantification of Pb (II) and Cd (II) in real water samples.



  • 1.

    Waheed A, Mansha M, Ullah N. Nanomaterials-based electrochemical detection of heavy metals in water: Current status, challenges and future direction. TrAC Trends Anal Chem. 2018;105:37-51. doi: 10.1016/j.trac.2018.04.012.

  • 2.

    Maleki B, Baghayeri M, Ghanei-Motlagh M, Mohammadi Zonoz F, Amiri A, Hajizadeh F, et al. Polyamidoamine dendrimer functionalized iron oxide nanoparticles for simultaneous electrochemical detection of Pb2+ and Cd2+ ions in environmental waters. Measurement. 2019;140:81-8. doi: 10.1016/j.measurement.2019.03.052.

  • 3.

    Afzali D, Fayazi M, Favi A. Displacement-dispersive liquid-liquid microextraction based on solidification floating organic drop trace amounts of lead in water sample prior to flame atomic absorption spectrometry determination. J Chilean Chem Soc. 2013;58(1):1593-6. doi: 10.4067/s0717-97072013000100020.

  • 4.

    Ghanei-Motlagh M, Fayazi M, Taher MA, Darezereshki E, Jamalizadeh E, Fayazi R. Novel modified magnetic nanocomposite for determination of trace amounts of lead ions. RSC Advances. 2015;5(121):100039-48. doi: 10.1039/c5ra20705c.

  • 5.

    Lung I, Stan M, Opris O, Soran ML, Senila M, Stefan M. Removal of lead(II), cadmium(II), and arsenic(III) from aqueous solution using magnetite nanoparticles prepared by green synthesis with box–behnken design. Anal Lett. 2018;51(16):2519-31. doi: 10.1080/00032719.2018.1446974.

  • 6.

    Zhang N, Shen K, Yang X, Li Z, Zhou T, Zhang Y, et al. Simultaneous determination of arsenic, cadmium and lead in plant foods by ICP-MS combined with automated focused infrared ashing and cold trap. Food Chem. 2018;264:462-70. doi: 10.1016/j.foodchem.2018.05.058. [PubMed: 29853402].

  • 7.

    Peng J, Li J, Xu W, Wang L, Su D, Teoh CL, et al. Silica nanoparticle-enhanced fluorescent sensor array for heavy metal ions detection in colloid solution. Anal Chem. 2018;90(3):1628-34. doi: 10.1021/acs.analchem.7b02883. [PubMed: 29275622].

  • 8.

    Izadkhah V, Rezaei M, Mahmoodi J. A new platform based on the Fe3O4 nanoparticles, ligand and ionic liquid: application to the sensitive electrochemical determination of the lead ion in water and fish samples. Anal Bioanal Chem Res. 2019;6(2):405-17. doi: 10.22036/abcr.2019.154674.1270.

  • 9.

    Ghanei-Motlagh M, Taher MA. Novel imprinted polymeric nanoparticles prepared by sol–gel technique for electrochemical detection of toxic cadmium(II) ions. Chem Eng J. 2017;327:135-41. doi: 10.1016/j.cej.2017.06.091.

  • 10.

    Ghanei-Motlagh M, Taher MA. An electrochemical sensor based on novel ion imprinted polymeric nanoparticles for selective detection of lead ions. Anal Bioanal Chem Res. 1999;4(2):295-306.

  • 11.

    Afkhami A, Khoshsafar H, Bagheri H, Madrakian T. Construction of a carbon ionic liquid paste electrode based on multi-walled carbon nanotubes-synthesized Schiff base composite for trace electrochemical detection of cadmium. Mater Sci Eng C Mater Biol Appl. 2014;35:8-14. doi: 10.1016/j.msec.2013.10.025. [PubMed: 24411345].

  • 12.

    Baghayeri M, Alinezhad H, Fayazi M, Tarahomi M, Ghanei-Motlagh R, Maleki B. A novel electrochemical sensor based on a glassy carbon electrode modified with dendrimer functionalized magnetic graphene oxide for simultaneous determination of trace Pb(II) and Cd(II). Electrochim Acta. 2019;312:80-8. doi: 10.1016/j.electacta.2019.04.180.

  • 13.

    Afkhami A, Bagheri H, Khoshsafar H, Saber-Tehrani M, Tabatabaee M, Shirzadmehr A. Simultaneous trace-levels determination of Hg(II) and Pb(II) ions in various samples using a modified carbon paste electrode based on multi-walled carbon nanotubes and a new synthesized Schiff base. Anal Chim Acta. 2012;746:98-106. doi: 10.1016/j.aca.2012.08.024. [PubMed: 22975186].

  • 14.

    Fayazi M, Taher MA, Afzali D, Mostafavi A. Fe3O4 and MnO2 assembled on halloysite nanotubes: A highly efficient solid-phase extractant for electrochemical detection of mercury(II) ions. Sens Actuators B Chem. 2016;228:1-9. doi: 10.1016/j.snb.2015.12.107.

  • 15.

    Fayazi M. Facile hydrothermal synthesis of magnetic sepiolite clay for removal of Pb (II) from aqueous solutions. Anal Bioanal Chem Res. 2019;6(1):125-36.

  • 16.

    Jin J, Fu L, Yang H, Ouyang J. Carbon hybridized halloysite nanotubes for high-performance hydrogen storage capacities. Sci Rep. 2015;5:12429. doi: 10.1038/srep12429. [PubMed: 26201827]. [PubMed Central: PMC5378895].

  • 17.

    Ghanei-Motlagh M, Taher MA. Magnetic silver(I) ion-imprinted polymeric nanoparticles on a carbon paste electrode for voltammetric determination of silver(I). Microchim Acta. 2017;184(6):1691-9. doi: 10.1007/s00604-017-2157-8.

  • 18.

    Ghanei-Motlagh M, Taher MA, Heydari A, Ghanei-Motlagh R, Gupta VK. A novel voltammetric sensor for sensitive detection of mercury(II) ions using glassy carbon electrode modified with graphene-based ion imprinted polymer. Mater Sci Eng C Mater Biol Appl. 2016;63:367-75. doi: 10.1016/j.msec.2016.03.005. [PubMed: 27040231].

  • 19.

    Fayazi M. Determination of H2O2 in human serum samples with novel electrochemical sensor based on V2O5/VO2 nanostructures. Ann Mil Health Sci Res. 2019;17(3). doi: 10.5812/amh.96175.

  • 20.

    Ghanei-Motlagh M, Taher MA, Fayazi M, Baghayeri M, Hosseinifar AR. Non-enzymatic amperometric sensing of hydrogen peroxide based on vanadium pentoxide nanostructures. J Electrochem Soc. 2019;166(6):B367-72. doi: 10.1149/2.0521906jes.

  • 21.

    Fayazi M, Afzali D, Ghanei-Motlagh R, Iraji A. Synthesis of novel sepiolite-iron oxide-manganese dioxide nanocomposite and application for lead(II) removal from aqueous solutions. Environ Sci Pollut Res Int. 2019;26(18):18893-903. doi: 10.1007/s11356-019-05119-9. [PubMed: 31077042].

  • 22.

    Tabak A, Eren E, Afsin B, Caglar B. Determination of adsorptive properties of a Turkish Sepiolite for removal of Reactive Blue 15 anionic dye from aqueous solutions. J Hazard Mater. 2009;161(2-3):1087-94. doi: 10.1016/j.jhazmat.2008.04.062. [PubMed: 18534746].

  • 23.

    Cornejo J, Hermosin MC. Structural alteration of sepiolite by dry grinding. Clay Minerals. 2018;23(4):391-8. doi: 10.1180/claymin.1988.023.4.06.

  • 24.

    Ghanei-Motlagh M, Fayazi M, Taher MA, Jalalinejad A. Application of magnetic nanocomposite modified with a thiourea based ligand for the preconcentration and trace detection of silver(I) ions by electrothermal atomic absorption spectrometry. Chem Eng J. 2016;290:53-62. doi: 10.1016/j.cej.2016.01.025.

  • 25.

    Fan HT, Li J, Li ZC, Sun T. An ion-imprinted amino-functionalized silica gel sorbent prepared by hydrothermal assisted surface imprinting technique for selective removal of cadmium (II) from aqueous solution. Appl Surf Sci. 2012;258(8):3815-22. doi: 10.1016/j.apsusc.2011.12.035.

  • 26.

    Fayazi M, Afzali D, Taher MA, Mostafavi A, Gupta VK. Removal of Safranin dye from aqueous solution using magnetic mesoporous clay: Optimization study. J Mol Liq. 2015;212:675-85. doi: 10.1016/j.molliq.2015.09.045.

  • 27.

    Zhu X, Liu B, Hou H, Huang Z, Zeinu KM, Huang L, et al. Alkaline intercalation of Ti3C2 MXene for simultaneous electrochemical detection of Cd(II), Pb(II), Cu(II) and Hg(II). Electrochim Acta. 2017;248:46-57. doi: 10.1016/j.electacta.2017.07.084.

  • 28.

    Tarley CR, Santos VS, Baeta BE, Pereira AC, Kubota LT. Simultaneous determination of zinc, cadmium and lead in environmental water samples by potentiometric stripping analysis (PSA) using multiwalled carbon nanotube electrode. J Hazard Mater. 2009;169(1-3):256-62. doi: 10.1016/j.jhazmat.2009.03.077. [PubMed: 19398268].

  • 29.

    Serrano N, Gonzalez-Calabuig A, Del Valle M. Crown ether-modified electrodes for the simultaneous stripping voltammetric determination of Cd(II), Pb(II) and Cu(II). Talanta. 2015;138:130-7. doi: 10.1016/j.talanta.2015.01.044. [PubMed: 25863381].

  • 30.

    Kadara RO, Tothill IE. Development of disposable bulk-modified screen-printed electrode based on bismuth oxide for stripping chronopotentiometric analysis of lead (II) and cadmium (II) in soil and water samples. Anal Chim Acta. 2008;623(1):76-81. doi: 10.1016/j.aca.2008.06.010. [PubMed: 18611460].

  • 31.

    Sopha H, Baldrianová L, Tesařová E, Grincienė G, Weidlich T, Švancara I, et al. A new type of bismuth electrode for electrochemical stripping analysis based on the ammonium tetrafluorobismuthate bulk-modified carbon paste. Electroanalysis. 2010;22(13):1489-93. doi: 10.1002/elan.201070010.